Methodology for Designing Forming Parts of Injection Molds Using Information Technologies
https://doi.org/10.17586/0021-3454-2023-66-3-241-246
Abstract
A method of designing forming parts of injection molds is presented. Results of analysis of the gating system parameters are presented in the form of a table of dependences on parameters of a polymer product. The obtained results can be used in the development of a knowledge base.
About the Authors
M. G. Lopatov
ITMO University
Russian Federation
Russian Federation
Maksim G. Lopatov Student; Faculty of Control Systems and Robotics
St. Petersburg
A. V. Chukichev
ITMO University
Russian Federation
Russian Federation
Artemy V. Chukichev - Post-Graduate Student; Faculty of Control Systems and Robotics
St. Petersburg
O. S. Timofeeva
ITMO University
Russian Federation
Russian Federation
Olga S. Timofeeva - PhD; Faculty of Control Systems and Robotics; Assistant
St. Petersburg
References
1. Markov A.M. Algoritm proyektirovaniya gruppovogo tekhnologicheskogo protsessa mekhanicheskoy obrabotki detaley (Algorithm for Designing a Group Technological Process of Machining Parts), Barnaul, 2012. (in Russ.)
2. Mitrofanov S.P. Osobennosti gruppovoy tekhnologii mekhanicheskoy obrabotki v sovremennykh usloviyakh (Features of Group Machining Technology in Modern Conditions), St. Petersburg, 2001. (in Russ.)
3. Barvinsky I. Polymer materials. Products, equipment, technology, 2018, no. 2, pp. 22–29. (in Russ.)
4. Pirogov A.V. Razrabotka i modelirovaniye protsessov tekhnologicheskoy podgotovki proizvodstva izdeliy iz polimernykh opticheskikh materialov (Development and Modeling of the Processes of Technological Preparation for the Production of Products from Polymeric Optical Materials), Candidate’s thesis, St. Petersburg, 2014. (in Russ.)
5. Gao H. Frontiers of Mechanical Engineering, 2018, vol. 13, pр. 85–95.
6. Mok C.K., Hua M. & Wong S.Y. International Journal of Production Research, 2008, no. 14(46), pp. 3783–3800, https://doi.org/10.1080/00207540601103100.
7. Low M., Lee K. Int. Journ. Adv. Manufac. Tech., 2003, vol. 21, рр. 807–819, https://doi.org/10.1007/s00170-002-1397-9.
8. Basov K.I., Braginsky V.A., Kazankov Yu.V. Formuyushchiy instrument dlya izgotovleniya izdeliy iz polimernykh materialov (Forming Tool for the Manufacture of Products from Polymeric Materials), Moscow, 1991. (in Russ.)
9. Kazmer D.O. Injection Mold Design Engineering, Hanser Publications, 553 р.
10. Kryzhanovsky V.K. Inzhenernyy vybor i identifikatsiya plastmass (Engineering Selection and Identification of Plastics), St. Petersburg, 2009, 204 р. (in Russ.)
11. Talapov V.V., Timofeeva O.S., Pompeev K.P. Innovatsii na transporte i v mashinostroyenii (Innovations in Transport and Mechanical Engineering), Proceedings of the IV International Scientific and Practical Conference, St. Petersburg, April 28–29, 2016, vol. 3, рр. 138–142. (in Russ.)
12. Menges G., Michaeli W., Mohren P. How to make injection molds, Hanser Publishers, Munich, 2001.
13. Rutkauskas Ž., Bargelis A. Mechanika, 2007, no. 4(66).
Review
For citations:
Lopatov M.G., Chukichev A.V., Timofeeva O.S. Methodology for Designing Forming Parts of Injection Molds Using Information Technologies. Journal of Instrument Engineering. 2023;66(3):241-246. (In Russ.) https://doi.org/10.17586/0021-3454-2023-66-3-241-246
Views:
8
Email this article 